Cheap chisel sets get reviewed by people who used them once, on a scrap of pine, for a single birdhouse. I am not going to do that to you. The HURRICANE 4 Piece Wood Chisel Set has been sitting on my bench for a year now, through a cherry blanket chest, two stacks of cutting boards, and more end tables than Carol wants in the house. I have sharpened them, dinged them, and knocked one off the bench onto the garage floor. What follows is what I actually found, including the parts that are not flattering to the set or to me.
Here is the short version for the people who want it. If you are a hobbyist working out of a small garage shop, and you need four sizes in a pouch that folds into a drawer, this set does the job. It arrives sharp enough to use, it re-edges quickly on a stone, and it will not leave you feeling like you were taken. What it will not do is hold an edge like a chisel that costs more than this whole set. That trade is the entire story of the HURRICANE set, and the rest of this article is me explaining where the line sits.
The Quick Verdict
A genuinely usable starter to mid set for a hobby shop. Sharp out of the pouch, fast to re-hone, and honestly limited in hard stock.
Amazon Check Today's Price →Four sizes that actually get used, in one pouch that folds flat
The 1/4 inch, 1/2 inch, 3/4 inch and 1 inch combination covers hinge gains, mortises, paring and cleanup. Blades arrive with guards fitted.
Amazon Check Today's Price on Amazon →How I've Used These Chisels, Which Is the Only Credential That Matters
Most of my chisel work is not glamorous. I am not carving acorns. I am cleaning out hinge gains on a neighbor's cabinet door, paring the end of a stretcher so it seats without a fight, and chopping four mortises on a bookshelf that has to fit up a rowhouse staircase. That is the work these chisels get, and it is a fair test, because a chisel that will not hold up to repeated light chopping in white oak is not a chisel I want living in the drawer.
The 3/4 inch is the one that lives in my hand. It chopped the mortises for a white oak bookshelf last spring and it pared the shoulders on the same job. The 1 inch got used for wider cleanup on the blanket chest, mostly taking the fuzz off the inside of a dovetail before glue up. The 1/2 inch is the general purpose middle child that does whatever is left. The 1/4 inch is the one that either works or does not, because a small chisel has less steel behind the edge, and this one needed a fresh honing before it behaved on end grain.
Number of chisels in this set I never touched: zero. That is not always true of sets. I have a four piece set from years ago where the 1/4 inch was ground so poorly that I gave up on it inside a week and it has been rusting in a coffee can ever since. The HURRICANE set at least got the grinding right on all four, and in a set at this end of the market that is the thing I expected to go wrong.
What the 25 Degree Bevel Means When You're Standing at the Bench
The listing says 25 degree bevel edge, and that is a sensible starting angle for general work. It is shallow enough to pare cleanly in pine and poplar, and it is roughly what I would grind on a chisel intended for everything from hinge gains to light chopping. What it is not is an angle that survives end grain in hard maple for long. Twenty five degrees is a fine edge and a fragile one. If you do a lot of end grain work, you will be touching it up more often, or you will be regrinding to 30 and living with the difference in how it feels going into the wood.
I tested this the boring way, because that is the only way I know. I pared end grain on a scrap of hard maple until the chisel stopped cutting cleanly, then honed it and counted. The CR-V steel in these blades is not the hardest steel I own, and it showed. The edge folded sooner than the two chisels I keep for finish work. But here is the part that matters in a hobby shop: it honed back in about two minutes on a 1000 grit waterstone, with no chipping and no hollow bevel that refused to sit flat.
Soft-ish steel that hones fast is not a defect. It is a trade. You spend more time at the stone and less at the counter. What you do not want is steel that is soft and gummy, where the edge smears instead of slicing. The HURRICANE blades are not that. They take a clean edge and they cut. They just do not keep it as long as a chisel that costs several times as much, and anyone who tells you otherwise has not used both side by side on the same afternoon.
It honed back in about two minutes on a 1000 grit waterstone, with no chipping and no hollow bevel that refused to sit flat. That is the whole value case for this set.
Edge Retention, Measured the Only Way I Can
I cannot give you a hardness number because I do not own a tester and I would be making it up. What I can give you is how many times I stopped to hone during a job. On the white oak bookshelf, with four mortises and a great deal of paring, I honed the 3/4 inch three times. On a batch of pine birdhouses I honed once for the whole run. On cherry, which is my favorite wood and the least forgiving of a dull edge, I honed every twenty minutes or so of steady paring and I could feel it going off before I stopped.
Compare that with the chisel I use for finish paring, which I honed once on the same bookshelf job. That is the honest gap and it is real. If you build furniture for a living, that gap costs you time every single day and it is worth paying to close. If you build a few pieces a year in a garage with a wood stove in the corner, three honings on a Saturday afternoon is not a hardship. It is the price of admission for the money you did not spend.
The other thing I noticed is that these blades are drop forged from CR-V steel and the four behave like siblings. I have owned sets where one chisel cut completely differently from the others, like it came from a different factory on a different day. These four feel consistent, ground the same way and finished the same way. In a set this inexpensive, consistency is the thing I would have bet against, and it is the thing that surprised me most over the year.
The Handles, the Fit, and the Two Things I'd Change
The handles are PVC with what the listing calls a regular grip. They are light, they are comfortable in a bare hand, and they get slick the moment your palm does. In July, in a garage with no air conditioning, that matters more than it sounds like it should. I wiped them down with a rag more than once and I thought about wrapping the 3/4 inch in hockey tape and decided against it because I did not want tape goo on the tool I reach for every week. I would not turn the set down over it, but I keep a rag on the bench now.
The second thing I would change is the strike question. The listing does not advertise a striking cap, and PVC is not a handle material I would trust under a mallet. So I do not hit these with a mallet. When a mortise needs real persuasion I reach for a chisel that was built for it. That is a limitation worth knowing going in, because some four piece sets sold to hobbyists are built to be struck and this one is not advertised that way. Read the listing closely instead of assuming.
The fit of the blades to the handles on my set was fine on all four, with no wiggle and no gap I could catch a fingernail in. I have read reviews from people who received a loose one, and I believe them, because quality control at this end of the market is never going to be perfect every time. Inspect all four when the box arrives. If one is loose, send it back. That is a five minute check that saves you a bad afternoon and a returned tool anyway.
The Pouch, the Guards, and the Storage Question
The set comes with a case, and the blade guards are the part I would keep even if I threw the pouch in the trash. A chisel guard is worth more than it looks like it is worth, because an edge nicked in a drawer takes ten minutes at the stone to fix, and a chisel that rolls off the bench onto concrete takes a good deal longer than that. I keep the two smallest guarded in a drawer and the two larger on the rack, and the guards have held up to a year of that without splitting at the seam.
The pouch itself is basic. Canvas, stitched, with slots that hold the four chisels and their guards. It lives in a bench drawer now, because I have a rack for the tools I use daily and the pouch is where the set goes when I carry it to a neighbor's house to fix a sticking door. For a small shop where every tool has to earn its footprint, a pouch that folds flat is the right answer. It is not a fancy roll and it does not need to be.
Sharpening: What These Blades Want From You
You do not need an expensive sharpening setup to keep these working. I use a 1000 grit waterstone, a 6000 grit for the final polish, and an inexpensive honing guide for the bevel because I cannot hold a consistent angle freehand to save my life. The 25 degree bevel makes the guide setting easy. Ten strokes on the coarse, ten on the fine, a quick pass flat on the back to knock off the burr, and you are back to work. The whole thing runs about two minutes per chisel once you have done it a few times and stopped thinking about it.
The one warning I will give you is about the back of the blade. Out of the pouch, the backs on my set were flat enough to work but not polished. If you only ever sharpen the bevel and never touch the back, you will chase a burr around for twenty minutes and conclude the chisel is bad. Flatten the back once when the set is new, keep it flat, and the bevel side stays simple forever. That is true of every chisel ever made, not just this one, and it is the single most common thing beginners get wrong.
What I Liked
- Sharp enough to pare pine, poplar and cherry straight out of the pouch
- 25 degree bevel is a sensible general purpose angle and easy to maintain
- Hones back fast on a 1000 grit stone with no chipping
- All four sizes get used, and the four blades behave consistently
- Blade guards are genuinely useful rather than an afterthought
- Pouch folds flat, which matters in a 12 by 20 foot shop
Where It Falls Short
- Edge retention trails a premium chisel, noticeably in hard maple
- PVC handles go slick with a sweaty hand in a hot garage
- Not advertised for mallet work, and I would not strike them
- Quality control is not perfect, so check all four on arrival
Who This Is For
This set is for the hobbyist who wants four working sizes without spending a fortune and who is willing to stand at a stone for two minutes now and then. It suits a small shop, a bench with a drawer, and a person who builds a handful of projects a year and wants the chisel to be the least interesting part of the job. It also suits a second set, the one that lives in a travel bag for repair calls, where you do not want to risk your good chisels in somebody else's kitchen with a door swinging off its hinge.
And it suits a beginner specifically, because the 25 degree bevel is forgiving to learn on. You are not going to ruin this chisel while you figure out how to hold an angle. You might ruin a premium one and feel sick about it for a month. Learn on the HURRICANE set, get your technique down, flatten a back or two, and then decide for yourself whether the upgrade is worth what it costs. That is the order I would do it in if I were starting over in this garage at sixty six instead of thirty six.
Who Should Skip It
Skip it if you cut dovetails in hard maple all day. Skip it if you are doing production work where every honing stop comes straight out of your pocket. Skip it if you expect a chisel to be struck with a mallet, because this set is not advertised for that and I would not do it in my shop. And skip it if you are shopping for a tool you plan to hand down to a grandchild, because that is not what this is and it never claimed to be.
None of that is a knock. It is a boundary, and a tool that is honest about what it is will serve you better than one that pretends. I have tools in this garage I bought for one job and kept for thirty years, and I have tools I bought cheap knowing full well they were cheap. The HURRICANE set is in the second category and it has done everything I asked of it, which is more than I can say for the drill press I am still mad about. That is a fair deal in my book.
A year on the bench, and the 3/4 inch is still the first chisel I reach for
Four sizes, 25 degree bevels, drop forged CR-V steel, guards and a pouch that folds flat. Expect to hone more often than you would with a premium set. Expect it to hold up anyway.
Amazon Check Today's Price on Amazon →